Access Control Accessories  (1,174)

Mortice panic device. Mechanisms made of galvanised steel. Cover made of satin stainless steel or plastic depending on the finish. Finishes: red or green, satin stainless steel (stainless steel version. Handing Din Left /Din right usable. Maximum wing width: 1300mm. Spindle angle turn: 30º or 45º depending on the model. Square spindle: 9mm.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The 1045 Series features a wider make distance, which permits faster installation, accommodates greater misalignment and works better on steel without time-consuming brackets. A wider break distance helps prevent false alarms caused by loose fitting doors. Interlogix specified contacts keep the 1045 Series from sticking or freezing on seldom-used doors.

Provides 1 input & 4 output ports, each optically isolated RS232 or RS485, with status LEDs.  Up to 16 DIGI*TRAC controllers per output port.  Cascading supported (2 levels deep).  Includes enclosure, 115 VAC power supply, battery, key lock.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

SCRAMBLE*NET Gateway/Globalizer.  Polling engine & encryption for Host PC communications to up to 63 DIGI*TRAC controllers (16 max without NET*MUX4.  16 max for MOMENTUM).  RS-232 (or RS-485, selectable) port for Host PC and RS-232 & RS-485 ports for DIGI*TRAC controllers.  Provides server independent globalization of credential limits and master control zones between Digi*Trac controllers on Velocity.  Includes 6' host RS-232 extension cable, transformer (120VAC to 12VDC, 250-500mA), alarm relay, & status LEDs.  Low profile plastic desktop housing.  UL Listed.

The Borer Lock Manager/Power Adapter enables a complete door installation including electric release, door sensor and card readers, to be centrally powered over a single 300m (1000 ft) length of CAT5/6 cable. This eliminates the need and costs of providing mains powered fused spurs at every door.Both Power and Data are supplied from the Borer Midspan Bridge using IEEE 802.3af (PoE) based power delivery systems.The Power Adapter/Lock Manager circuit board has a small footprint and is designed to be mounted together with the "Press to Exit" switch in a single gang electrical - wall box.It performs the following functions: Breaks out the power and data supplied down a standard CAT5e cable by a Borer Midspan Bridge Monitors door status settings (door open, lock status and exit request button pressed) Manages the power supplied to operate a solenoid operated door lock or strike. These need an initial high current to engage the solenoid and then a reduced static current to maintain it. The power delivered by most systems is not current restricted which will cause the lock, after it has been switched, to continue to consume power. The extra energy consumed raises the temperature of the solenoid. By managing and limiting the power delivered, less heat is generated. As a result, less energy is used and the lock is not stressed, extending its operational lifespan. Power over CAT5e cable technology is used to power equipment where it is inconvenient, expensive or not possible to provide a separate mains power outlet.This solution requires two components as follows: A Midspan Bridge at the source, which injects power into a standard CAT5e cable system without affecting the data A Lock Manager/Power Adapter at the destination, which splits power and data for delivery to local devices. The power management chipset employed (IEEE 802.3af standard), is designed for Power over Ethernet applications, providing protection against short circuit, polarity reversal and the accidental connection of non-compliant equipment.For door access control applications the Power Adapter/Lock Manager is located on the secure side, either in the "Press to Exit" switch housing or next to electric release.Communications between the Lock Manager and Card Reader is via a four core cable which supplies encoded data and power. This enhances security by removing the opportunity to gain access by dismantling the card access reader head and shorting out the lock or power supply cable ends.Benefits: Enhances Security preventing door access by tampering with the card access reader head or controller Safeguards the Electrical Equipment connected to the circuit by only supplying power following device identification and evaluation Protects the CAT5e Cable by measuring the energy delivered providing a 48 Volts current limited power source Reduces Equipment Cost by eliminating the requirement for local main outlets, power supply and battery at every doorReduces Installation Cost by eliminating the local mains wiring, which in most countries, for legal or insurance reasons, has to be installed by a qualified and/or licensed electricianUp to 80% Reduction in Energy Consumption by managing the power being supplied to operate the electric door release      

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

Exit buttons may be used with Compact, Switch2 or Net2 systems.  They are designed to match our range of PROXIMITY readers and keypads.  The exit buttons are supplied with a choice of black or white fascias which can be fi tted in the final stages of installation. 

Monitors unauthorised opening and closure of doors or windows Ultra-thin design at only 4mm thickness Discreet mounting in doors and windows Powered by a pre-inserted long lasting battery Minimum power consumption Faster speed of signal transmission, reliability, and enhanced communication range Supervisory signals ensure proper operation Low battery detection Simple and flexible wireless installation Suitable for residential and commercial premises

Powered by pre-inserted Lithium battery for easy installation Mounted on door or window frames Tamper protection to prevent unauthorised removal, sabotage or unsteady installation Randomised supervision signals for system integrity checks and troubleshooting Low battery detection Power magnet allows for overall side-to-side gap distance of 32mm LED serving as a fault and test mode indicator Compliant with CE requirements Certified to Standard: EN 50131 Grade2, ClassⅡ

The Extra Large Enclosure (XL) is a universal sturdy metal enclosure designed for general purpose installation of either Inner Range Integriti or Concept equipment. The flexible design allows for the complete range of Integriti or Concept equipment to be fitted in various custom configurations to meet almost any installation requirement. A range of powered or non-powered models are available. The XL's low profile side elevation protrudes less than 90mm from the mounting surface.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

Aritech 1078CW-N is a recessed steel door contact with wire leads. It is designed specifically for use in the steel doors commonly found in commercial building applications. The magnet housing isolates the magnet from the surrounding steel for maximum gap distances, both make and break.

Aritech 2847T-M is a explosion proof conduit fitting magnetic terminal contact with SPDT switches.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

Alpro ALP-DR-EN-980 is a surface door closer with standard arm. It is suitable  suitable for right or left hand installation and is easy to install, use and adjust.

Exit buttons may be used with Compact, Switch2 or Net2 systems.  They are designed to match our range of PROXIMITY readers and keypads.  The exit buttons are supplied with a choice of black or white fascias which can be fi tted in the final stages of installation. 

Aritech 1078CW-G is a recessed steel door contact with wire leads. It is designed specifically for use in the steel doors commonly found in commercial building applications. The magnet housing isolates the magnet from the surrounding steel for maximum gap distances, both make and break.

Aritech 2105A magnetic contact features closed loop and stainless steel armoured cable. It is used to protect valuable free-standing items that are stored outdoors. The high-impact plastic housing protects the contact from corrosion or high resistance buildup.

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing End loading option Variable strength

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing End loading option DDA compliant 90° hold open facility

Alpro ALP-DR-EN-28A is a surface door closer with standard arm and backcheck. It is suitable for right or left hand installation and is easy to install, use and adjust.

Comes with charger circuit. Available in small metal case. Also comes without charger circuit (models ARD).

Request-to-exit button with key icon Flush mount To open the door from the inside, if access is only being monitored from one side

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

Alpro DDA-NHO-T2-U transom door closer is designed to be concealed within the transom header bar of the door. It provides controlled closing of a single or double action aluminium door or doors.

ALP-DR-EN-170 is a surface door closer with sliding track and arm. It is suitable for right or left hand installation and is easy to install, use and adjust.

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing Side loading option DDA compliant

The Functional 97 Series of pull door handles are manufactured in 41mm diameter for Satin Anodised (SAA) and Painted Nylon Coated (NC). These pull door handles are designed for aluminium, timber and glass door applications.  Finishes for 38 diameter are Stainless Steel (SSS) and Polished Stainless Steel (PSS). They come in a range of sizes up to 3000mm. All sizes are available in either straight or offset versions and are suitable for bolt-thru (single side fixing) or back to back fixing.  Features Include Variety of Finishes Available in Straight and Offset versions

Alpro DDA-NHO-T3-U transom door closer is designed to be concealed within the transom header bar of the door. It provides controlled closing of a single or double action aluminium door or doors.

12, PSU

Exit buttons may be used with Compact, Switch2 or Net2 systems.  They are designed to match our range of PROXIMITY readers and keypads.  The exit buttons are supplied with a choice of black or white fascias which can be fi tted in the final stages of installation. 

The Alpro Hardware Division of IEC Limited has announced the release of the new Alpro PB86 proximity switch. Designed to be used in conjunction with the full range of Alpro electric strikes, electric bolts and general access control products out in the field, this proximity switch offers contactless features offering sterile and hygienic operation. The switch has a proximity distance adjustable from 5-20cms, along with an adjustable relay trigger from 1 to 9 seconds. The switch has easy indication of operation status and can be operated remotely by a small keypad. The switch is suitable for indoor use only. A simple swipe of the hand operates the switch, ensuring no contact is required. A feature especially important with the onset of MRSA and other infectious bacteria currently prevalent in hospitals and other communal areas. Keith Parry Alpro's Divisional Sales Manager commented: "In line with our ongoing product development and taking full cognisance of the macro environment, we have brought this new proximity switch to the market, to fulfil market requirements. It is competitively priced and along with Alpro's proven track record of service and reliability will prove to be a winner. Once again reinforcing Alpro's commitment to excellence, making us first choice for locking products."

Genie dome request to exit button - white low profile plastic - surface mount

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing Side loading option Heavy Duty 90° hold open facility