Access Control Accessories  (1,151)

Everswitch SML1 is a 22.5mm illuminated switch with 12” AWG 24 wires, in a wide rang of dimensions.

Everswitch SMF2 is a 16 mm switch. It is ideal for use in rough environments.

Everswitch SMF4 is a 16 mm switch with IP68 protection. It is ideal for use in rough environments.

Everswitch SBF2 18.6 mm switch is sturdy, long life, with no moving parts, 100% sealed, resistant to EMI and RFI and needs no power supply.

Altronix DL1 is a 1 second to 1 minute door control timer that is used for basic door operation. This timer can be activated with a momentary or maintained trigger. Input12 volt - 24 volt AC or DC operation. RelayDry relay output (1 form "C" contact, rated @ 2A).12VDC regulated beeper output. FeaturesIsolated AC or DC voltage 5V-24V trigger.Time adjustable from 1 second to 1 minute.Momentary or maintained trigger. Visual IndicatorsIndicates relay is energized. TemperatureOperating 0ºC to 49ºC (32ºF to 120ºF).Storage - 20ºC to 70ºC ( - 4ºF to 158ºF).Relative Humidity 85% +/- 5%.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC or 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and/or 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and/or 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

The Everswitch SBR3 27 mm illuminated switch is rugged, extremely durable, and with no moving parts. Switch is immune to ESD and generate no EMI or RFI. A power supply is not needed for switch operation.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

GB/UHR903 is a radio frequency vehicle access receiver (it can used with the GB/XQT904 transmitter). It connects 2 vehicle receivers per IXP220 (GB/IPS963) system controller or GB/IPS920i door controller with the GB/UHR903 being within 10m of the controller.

BPT GB/ITR901 is an infrared receiver (use with the GB/IVT900 vehicle transmitter that requires installation in the vehicle). Connect 2 vehicle receivers per IXP220 (GB/IPS963) system controller or GB/IPS920i door controller with the GB/ITR900 being within 8m of the controller.

BPT IMPRO B-SHO oscar door control unit

Morse Watchmans Tamper Proof Key Ring 1.5" x 1.5" incorporate ease-of-use, a tamper-proof locking mechanism and unique identification system while offering the flexibility to add or remove keys without destroying the more expensive ring. It has a replaceable hub technology that allows to re-use the tamper proof key ring and replace the hub at a fraction of the cost.

Gallagher provides specialized cables ideal for the high speed HBUS communications protocol, and use in the installation of security systems. An outdoor version is also available for use in installations that require additional protection from the environment. Features and benefits: Superior voltage drop performance for the DC supply conductors, equivalent to three times the distance of a CAT5 cable. Stranded conductors to allow easy distribution to multiple devices. Wire sheaths match HBUS colours for easy recognition. 300 meters of HBUS in an easy-feed box. 1 meter markings along the entire cable.

The ACS5000-DB dual reader expansion board provides two additional Wiegand reader inputs to the Brivo ACS5000 series control panels. Each reader node (input) provides (1) form C (SPDT) output relay for lock power switching, (1) dedicated request to exit input, (1) dedicated door position switch input, (2) auxiliary inputs, and (2) auxiliary Form C (SPDT) output relays.

The PD130 inductive loop detector is the most critical component of the whole vehicle access control system. Single channel loop detectors are used to identify the presence of vehicles by means of an inductive loop buried under the road. These "one chip" microprocessor-based units benefit from a detect filter and frequency indicator and are suitable for parking control and motorised door or gate applications. All detectors are CE tested and approved. A compact detector diagnostic unit is available for extracting data from new and existing sites.

Verkada BR12-HW is a wired surface mount door contact - 5 pack

Gallagher provides a high-level integration between Command Centre and the Croene Electronic Key Cabinet. This integration allows Command Centre to manage user access to keys within the cabinet. Access to the cabinet can be provided to specific users at specified times. Users can be identified by PIN, MIFARE®, or DESFire credential. No additional hardware, devices, or software licenses are required. Creone cabinets are available in a range of models and sizes to suit your business.  Key cabinets can be expanded by adding more compartments or key hooks as required and can be spread across multiple geographical locations while being monitored centrally.

This integration is a high-level interface facilitating control and management of C.Q.R.iT® and C.Q.R.iT® eXtreme key cabinets and locker systems via Gallagher Command Centre. To eliminate manual and duplicate data entry, Cardholders and Access Groups are automatically imported from Gallagher Command Centre into the C.Q.R.iT® key cabinets and lockers. Cardholders inherit access based on their Access Group membership and can instantly use allocated Keys and Assets stored in the key cabinets and lockers. All transaction log data from the keys cabinets and lockers, including alarms, are sent back to Gallagher Command Centre to provide a centralized reporting facility, eliminating the need for staff to monitor separate systems. The interface can also be configured to employ Gallagher Command Centre Anti-Tailgating features to prevent Cardholders from exiting the facility if they have not yet returned their keys or assets to the relevant cabinet or locker.

Verkada BR13-HW is a wired recessed mount door contact - 5 pack

DIGI*TRAC spare parts kit.  Includes: MPB1 (memory protection battery - replacable), FKIT (fuse assortment and fuse holder), one HDR (heavy duty relay - door), one MDR (medium duty relay - alarm).

GT-7042 is a PowerCheck interface/charger.

The RSIP is a sleek and compact Serial-to-Ethernet device server, providing quick and easy Ethernet connectivity to virtually any device or machine with a serial interface. Limit cabling costs by using the existing LAN / WAN network! This module allows RS232 modules and the CTV900ATR to communicate on a LAN / WAN network - avoiding the use of cables. Using standard communication software configuration, the RSIP allows for easy programming and installation. Always be aware of the module's status thanks to a detailed LED display. Use TCP/IP protocol to RS-232 Static IP address RJ-45 connection to the LAN RS232 serial connector included Supports TCP/IP, HTTP, ICMP and ARP Ethernet compatibility: Version 2.0 / IEEE 802.3. 10 MBPS - Semi Duplex Baud rates: 9600, 19200 and 38400 bps Transmission line format: 8 data bits, 1 stop bit No parity

Alpro 5212 is an armoured strike used for increased jam protection.

Enables existing sites to retrofit PaxLock Pro The cover plate discreetly hides any remaining holes or markings, allowing to save time and money on refurbishment

GT-7044 is a PowerCheck charger.

Morse Watchmans Tamper Proof Key Ring 2" x 2.5" incorporate ease-of-use, a tamper-proof locking mechanism and unique identification system while offering the flexibility to add or remove keys without destroying the more expensive ring. It has a replaceable hub technology that allows to re-use the tamper proof key ring and replace the hub at a fraction of the cost.

Pivoting mount technology and central wire entry for tensioner and wire alignment. Easier, more intuitive installation. Reduced fence installation time. Continuous conductive path. Retrofittable. Easier maintenance and trouble shooting. Rated for continuous outdoor use. Compatible with previous generation products - fits standard Gallagher security posts.

Equipped with an ID microchip and a 1/8” stainless steel locking ring on the standard model, or an 18-gauge wire steel ring on Quick-Fit, SmartKeys attach to one or more keys and provide robust security and data about their usage. When a SmartKey is inserted into a key slot in one of our key control cabinets, the ID microchip data is logged and the key set is marked as returned. When keys are removed, the SmartKey microchip data is retrieved and associated with the user removing the keys. In KeyWatcher systems, SmartKeys are locked in place until an authorized user is granted access, guaranteeing an even higher level of key security. Two types of SmartKeys are available, Standard and Quick-Fit. Standard SmartKeys are ideal for more permanent uses, allowing for up to three ring replacements on a single SmartKey. Quick-Fit SmartKeys allow administrators to add and remove keys more easily and as often as needed without having to replace the SmartKey itself. SmartKeys are offered in a variety of colours for easy identification and organization when using multiple key control systems in different facilities.

Reader cable 10 core CR9540 100m roll.  Conductor resistance 8.55 Ohms/km.  6.2mm diametre.

GT-7055 PK-3002 is a 1-37-4 driver handle with bit.

Euro profile cover plate kit, 70-72mm Enables existing sites to retrofit PaxLock Pro The cover plate discreetly hides any remaining holes or markings, allowing to save time and money on refurbishment

Paxton Access 901-016 is an 8mm split spindle for use with PaxLock Pro.

Paxton Access 900-059 is a door kit to use with the PaxLock Pro for doors with a width of 50-54mm.

Paxton Access 900-071 is a 9mm spindle kit to help install the PaxLock Pro with ease.

Secure SmartKeys for the Removal of U-Rings Remove SmartKey U-Ring Fragments Split and Remove KeyRing Hubs Spread Open Key Rings Add a Hub to a KeyRing and Seal

Re-useable 5/32″ stainless steel locking key rings A smart-switch solution that replaces your old welded and crimped rings Incorporates the cost-saving Replaceable Hub Technology Serialized/colour-coded hubs to identify tamper proof key rings and prevent substitution

Reader cable 10 core CR9540 10m roll.  Conductor resistance 8.55 Ohms/km.  6.2mm in diametre.

GT-7046 is a PowerCheck interface/charger & charger & charger (triple nest).