Access control systems & kits  (1,016)

Sentinel Barcode Clocking Station. Controlsoft's Sentinel AC-2001 bar code clocking station offers cost-effective and reliable bar code based identification. Infrared slot reader technology provides added security by allowing the reader to recognise "invisible" bar codes. The integrated software-configurable decoder supports most of bar code symbologies.

Low level with button feedback UniBus connectivity Compatible with a range of Integriti host modules Manage 16 floors per device UniBus loop-through connectors Connect up to 6 devices per Integriti host module Wide range of button input voltages Button sense input per floor Override input to allow free access mode Isolation between lift and Integriti system Firmware upgrade over-the-wire Integriti “B” size footprint 200 x 94mm Can be installed above other “B” size PCB’s

The Digi One RealPort device server is designed for standard serial-to-Ethernet connectivity. It is ideal for applications requiring seamless integration to existing application environments and network device management. Network Protocols TCP/IP, UDP, HTTP, PPP, TelNet, SNMP, DHCP, RARP. RJ-45 serial port; EIA-232 interface.

High performance, integrated Ethernet connectivity. The Digi One EM offers equipment manufacturers a quick, simple and cost-effective way to add network connectivity to their products. Network Protocols TCP/UDP, UDP Multicast. TTL Serial Interface.

RS485 connection to the AMC2 controller 8 inputs & 8 outputs extension board, up to three per AMC Status of inputs and outputs shows on AMC2 LCD display Transfer rate to EXT interface (RS485): 9,6kBit/sec

Sentinel Card Reader Controller with Clock & Data interface. Supported by Controlsoft KeyMasterPro and KeyMasterLite software.

The Digi One TS makes it possible to connect any serial device to the network. It is ideal for applications requiring seamless integration to existing application environments and network device management.

The 433 MHz Wavetrend stub antenna has been designed for optimal RF receiving performance with the Wavetrend reader range. This antenna attaches to the reader via a BNC(M) connector. This antenna has an omni-directional reception pattern around the vertical axis with null points being at the extreme ends of the stub. The antenna is housed in a rugged waterproof rubber mould that is UV resistant and can be used outdoors.

The Wiegand interface Unit converts data from the W-series Wiegand tags and W-RX201 reader to standard Wiegand (26 and 32 bit selectable) protocol as commonly used in the Access Control Industry. The unit comprises of a plug-in module, consisting of an 8-way screw terminal for the input wires from a W –series Reader and an 8-way terminal for the seven wires to a Wiegand access controller. The Wiegand Interface allows a W-series Reader to interface the W-series Wiegand tags into existing Access Control and Security Systems.

Sentinel Proximity Clocking Station. 20 character x 4 line baclit LCD screen. The Controlsoft Sentinel AC-2000 Philips HITAG™-based proximity clocking station provides reliable contactless identification and transaction capability. RS-485 serial port with user-selectable baud rate of 9600 or 19200. Up to 7 units can be multi-dropped using a single twisted pair cable.

The Controlsoft Sentinel AC-2002 magnetic strip clocking station is ideal for applications demanding inexpensive ID cards that comply with a widely available card format. The AC-2002 can be set up to read ISO tracks 1, 2 or 3.

AC-2100 operator station incorporates a high contrast 20 character x 4 line backlit LCD screen and a 21 key tactile keypad. In addition to providing basic communication with operators, the AC-2100 can also be configured as an arming and disarming station in the KeyMaster Pro intrusion alarm manager. RS-485 serial port with a maximum baud rate of 19200. Up to 7 units can be multi-dropped using a single twisted pair cable.

The 24 auxiliary expander board provides an additional 24 auxiliary outputs for the Universal zone expander module, along with extra power supply connections that may be required for devices connected to the outputs. Other features include 24 open collector outputs, LAN communication utilisation from the host universal expander module, output capability of switching up to 100 mA, quick and easy installation with no additional enclosure required and cost effective auxiliary expansion option.

RS485 connection to the AMC2 controller 16 inputs & 16 outputs extension board, up to three per AMC Status of inputs and outputs shows on AMC2 LCD display Transfer rate to EXT interface (RS485): 9,6kBit/sec

The Link-it™ RFID Receiver detects and decodes RF transmitted signals from Tags. Interpreted data is converted into electrical information that is passed down the Reader-net (Network of readers). Each Receiver in a Link-it™ Active Tagging System is programmed with a unique Receiver address. Receivers can be used in stand-alone mode or in a multi-drop asynchronous network. Mounting the Receiver depends on the type of application. The standard method is fixed screw mounting.

CyberLock CKS-030 web station is designed to work as a stand alone communication device. Once it is configured on a computer with either CyberAudit Professional or CyberAudit Enterprise management software, it can be placed indoors, anywhere there is a RJ-45 network connection. The Web Station updates and authorises any CyberKey smart key from a remote location via LAN or over the Internet. It can also be used to charge rechargeable CyberKeys. The Web Station is compatible with all CyberKey smart keys.

The CyberKey Web Authoriser Hub 2 includes significant increases in speed and memory, compatibility with Generation 2 CyberKeys, and enhanced network encryption Serves as the interface between CyberLock hardware and CyberAudit management software Key activity downloads and key permission updates occur simultaneously Offers multiple functions, such as charging the key battery or storing unprogrammed keys

CyberLock CKV-020S is a vault 20S key cabinet designed to program and dispense up to 20 CyberKey smart keys. The keys are stored in the locked cabinet unprogrammed until an approved RFID card or PIN is presented. After reading the RFID card, the cabinet communicates with the server and programs a key with that user’s permissions and opens.

The CyberKey Web Authoriser Hub 2 includes significant increases in speed and memory, compatibility with Generation 2 CyberKeys, and enhanced network encryption Serves as the interface between CyberLock hardware and CyberAudit management software Key activity downloads and key permission updates occur simultaneously Offers multiple functions, such as charging the key battery or storing unprogrammed keys

The REG Sentry is the first automated vehicle access control system. It consists of a control box with embedded processing engine, a choice of license plate capture cameras to accommodate a range of capture distances and easy-to-use Sentry Viewer software. The system delivers a flexible, user-friendly ANPR solution for a wide range of access control applications.

CyberLock CKS-F30 web station is designed to work as a stand alone communication device. Once it is configured on a computer with either CyberAudit Professional or CyberAudit Enterprise management software, it can be placed indoors, anywhere there is a RJ-45 network connection. The Web Station updates and authorises any CyberKey smart key from a remote location via LAN or over the Internet. It can also be used to charge rechargeable CyberKeys. The Web Station is compatible with all CyberKey smart keys.

The lift interface board provides 8 opto-isolated zone inputs and 8 relay outputs to facilitate connections to lift control systems for the purposes of controlling and monitoring access to floors. The system enables specific floor buttons to be activated according to the programmed options for that user. The Concept 3000 / Access 4000 supports lift control with or without button feedback. The button feedback feature ensures that only one floor is selected per valid card read.

MAXxess Systems have released an input module which enables security systems to be expanded with additional sensor / devices without the significant expense of additional controller / processors. Cost effective and flexible system expansion is made possible for both new and retrofit applications by the MAXxess Input Module modular, open architecture design which is compatible with AXxess™ Software, Random Access Memory Modules (RAMM™) and BLP™ 200 Series Processors.Key application benefits include: Extra 12 inputs per module -manages up to 8 fully supervised and additional 4 unsupervised digital inputs Individual input control - each input are individually configured, disabled or inverted. Networkable - via industry standard RS-485 communications Reduced cost - derived from less need for costly hardware and reduced installation time

CEM DIU/700/210 is a compact door interface unit designed to provide power to a door lock, as well as local power to a CEM reader when a high level of security is required. improves door security, by allowing the installer to locate lock controls on the secure side of a door, with an intelligent CEM reader on the unsecured side.

The Inovonics RF Expander connects directly to the Integriti or Inception RS-485 LAN Each Expander will provide up to 32 wireless detection zones Low Battery supervision & reporting from all wireless devices Frequency selectable to suit AU/NZ RF bands PCB only kit option available (for Europe only) World-renowned high quality RF wireless solution

CEM Systems DIU 230 offers a complete IP based access control solution that eradicates the need to provide local mains power at the door. The unit installation is classed as low voltage and can be completed by IT network installers without the expense of an electrician or electrical contractor.

The 8 relay expander provides low voltage, high current relay outputs, offering a general purpose interface in applications such as warning devices, air-conditioning, process control access control including door locks, lift call and lift floor selection. One board can be directly connected to the control module via a ribbon cable to provide 8 relay outputs. It has all the functionality of the control module version but is designed to plug into the universal expander.

CEM DIU/700/200 is a compact door interface unit designed to provide power to a door lock, as well as local power to a CEM reader when a high level of security is required. improves door security, by allowing the installer to locate lock controls on the secure side of a door, with an intelligent CEM reader on the unsecured side.

I-Code is the technology for smart labels, combining the advantages of barcode, Electronic Article Surveillance (EAS) and traditional RFID solutions. I-Code IC's are offering a low-cost, reprogrammable and disposable solution for source tagging, automatic data capture, theft protection and data storage on a product or its packaging. Read/write memory size 512 bits.

The Zebra P330i performance line card printer prints single-sided full colour or monochrome cards for access control and membership/loyalty card applications.  Designed and built for demanding environments, the P330i delivers reliability and performance for high-volume card production.  This single-sided, full colour card printer offers expansion options for networking and card encoding.  Printer speed 144 cards/hr.  Features and options include revolutionary angled card feeder design, 3-track magnetic stripe encoding, contact chip encoder, MIFARE contactless encoder, USB plug-and-play setup and 10/100 Mbps Ethernet connectivity.

CyberLock CKV-F01 is a key cabinet designed to program and dispense a single CyberKey. The Vault reads most unencrypted 13.56 MHz RFID cards and also recharges the keys with rechargeable batteries. The front of the Vault has an RFID card reader as well as status indicator lights.

Brivo Systems B-ACS6000-MBE is a 2 reader main controller board.

The Zebra P110i card printer prints single sided, full colour (300dpi print resolution) or monochrome access control and membership/loyalty cards in moments.  Printer speed 30 seconds/card.  It offers optional automatic card-feed or CardSense™ single card-feed mode.  Features include Load-N-Go™ drop-in ribbon cartridge and iSeries auto ribbon detection for tool-less ribbon replacement.  Optional magnetic encoder, 3-track HiCo/LoCo.  The sleek design uses high strength plastics and advanced electronics for reduced size and weight. Communications interface options are USB plug-and-play setup or 10/100 Mbps Ethernet.

The Zebra P430i performance line printer prints dual-sided full colour or monochrome cards for access control and membership/loyalty card applications.  Designed and built for demanding environments, the P430i delivers reliability and performance for high-volume card production.  Printer speed 102 cards/hr dual-sided (YMCKOK), 130 cards/hr single-sided (YMCKO).  Features and options include revolutionary angled card feeder design, optional 3-track magnetic stripe encoding, contact chip encoder, MIFARE contactless encoder, USB plug-and-play setup or 10/100 Mbps Ethernet connectivity.

The Zebra P630i security line printer prints dual-sided, full colour, tamper resistant identification cards with added single-sided lamination.  Printer speed 120cards/hr.  The P630i uses micro-positioning card transport system for enhanced colour photos.  Features and options include linerless and waste free 1.0 mil lamination, ID/Key security, 3-track magnetic stripe encoding, contact smart card encoding, linear barcode scanner.  Custom laminates available upon request: Holographic images, Special OVD images, UV images.

Zebra's single-sided, P100i printer uses ATM style CardSense™ single card-feed technology, producing full colour (300 dpi print resolution) or monochrome access control and membership/loyalty cards in moments.  Printer speed 35 seconds/card.  Features and options include; magnetic encoder, contact and contactless smart card encoders, 10/100 Mbps Ethernet and USB plug-and-play set up.  The compact and lightweight design fits in a variety of environments and also contains a convenient integrated storage bay for 100 cards and a cleaning roll.

The Zebra P640i security line printer prints dual-sided, full colour, tamper resistant identification cards with added dual-sided lamination.  Printer speed 120cards/hr.  The P640i uses micro-positioning card transport system for enhanced colour photos.  Features and options include linerless and waste free 1.0 mil lamination, ID/Key security, 3-track magnetic stripe encoding, contact smart card encoding, linear barcode scanner.  Custom laminates available upon request: Holographic images, Special OVD images, UV images.

The Zebra P330m performance line card printer prints single-sided monochrome cards for access control and membership/loyalty card applications.  Printer speed 600card/hr.  Designed and built for demanding environments, the P330i delivers reliability and performance for high-volume card production.  This single-sided, monochrome card printer offers expansion options for networking and card encoding.  Features and options include revolutionary angled card feeder design, 3-track magnetic stripe encoding, USB plug-and-play setup and 10/100 Mbps Ethernet connectivity.

The Zebra P120i card printer prints dual-sided, full colour (300dpi print resolution) or monochrome access control and membership/loyalty cards in moments.  Printer speed 40 seconds/card.  It offers optional automatic card-feed or CardSense™ single card-feed mode.  Features include Load-N-Go™ drop-in ribbon cartridge and iSeries auto ribbon detection for tool-less ribbon replacement. Optional magnetic encoder, 3-track HiCo/LoCo.  The sleek design uses high strength plastics and advanced electronics for reduced size and weight.  Communications interface options are USB plug-and-play setup and 10/100 Mbps Ethernet.

Now with new, easier-to-use onscreen icons, Morse Watchmans’ KeyWatcher Touch enterprise key control and management system has a large touchscreen and user-intuitive interface. KeyAnywhere lets you return a key to any KeyWatcher in your enterprise. Locate which KeyWatcher a specific key is in or find who has it with KeyFind. Every transaction is automatically recorded. With improved integration capabilities, patented SmartKey system, modular design and full scalability, we just keep making key management better.